Error codes

[ricked1]

Does anybody know if there is a chart with error codes?  I was going to work today and when I turned the key instead of showing LO it showed D2000016.  I tried to start it three times and it would crank but not start.  I turned the key off and on again, the code was gone and it started right up.  I have made many short trips today and have not seen this problem since.  On the way home the seat seamed to be getting warm, I took the seat off and could not feel anything warm.  I had the wire recall done in November.  I am using a EJK and currently have the air boot on, I am still waiting for my exhaust to arrive (might be a few weeks for Yoshimura).  Other wise the bike is running great.  Has anybody had similar problems?  Thanks.

[Guest Ralph]

16 seems to be "rear wheel sensor open circuit" so if its a abs bike
check the wiring and connections to the rear abs sensor, but would not
think that would stop it starting.
depending on how you read them it could be the Atmospheric sensor.
that would make sense as the engine wont run, especially if the air boot
what ever that is messes with air pressure.
 
Below is a list of Yamaha codes but not specific to the 07.
 
 
 
01 : Throttle position - must be from 15-17 (closed) to 97-100 (opened)
 
02 : Atmospheric pressure given in mmHg (normal is 760 - average weather)
 
03 : Differential pressure between air and intake pipe
 
05 : Air intake temperature (in Celcius)
 
06 : Cooling liquid temperature (in Celcius)
 
07 : Absolute speed (must be 000 in garage). Check with rear weel.
 
08 : Lean angle safety switch control - must be from 0.4-1.4 (upright) to 3.8-4.2 (horizontal). DISMOUT THE SWITCH FOR CHECKING !!!
 
09 : Battery voltage - must be above 12.0
 
20 : Side stand switch - displays ON or OFF
 
21 : Neutral gear switch - displays ON or OFF
 
 
 
Part II : ECU memory check.
 
 
 
60 : EEPROM error code presence - 00 means no default, 01 or 02 means default on corresponding cylinder (blinks if both cylinders).
 
61 : Error Code memory log - Displays 00 if no error code in memory, displays the Error Code if any (11 to 50). Display changes every two seconds if more than one Error Code in memory, then start again from first.
 
62 : Displays the number of Error Code in memory. To clear the memory, switch the Engine Run Switch to ON position (no backup).
 
70 : Check Code number, display from 0 to 255
 
 
 
Part III : Activators - To activate, turn Engine Run switch from OFF to ON - Engine check light is activated too.
 
 
 
30 : Coil 1 is activated 5 times per second.
 
31 : Coil 2 is activated 5 times per second.
 
36 : Injector 1 solenoid is activated 5 times per second.
 
37 : Injector 2 solenoid is activated 5 times per second.
 
48 : Air duct solenoid is activated 5 times per second.
 
49 : Air intake solenoid is activated 5 times per second.
 
50 : Fuel injection relay is activated 5 times per second.
 
51 : Cooler fan is activated every 5 seconds.
 
52 : Headlight relay is activated every 5 seconds (2 seconds ON, 3 seconds OFF) - 2003+ model only.
 
 
 
Error Codes
 
 
 
Error Number 11 : Cylinder identification sensor error - DIAG mode (none)
 
Error Number 12 : Crankshaft posiiton sensor error - DIAG mode (none)
 
Error Number 13 : Air intake pressure sensor error - DIAG mode 03
 
Error Number 14 : Air intake duct error - DIAG mode 03
 
Error Number 15 : Throttle position sensor error - DIAG mode 01
 
Error Number 19 : Sidestand sensor error - DIAG mode 20
 
Error Number 20 : Air pressure sensors error - DIAG mode (none)
 
Error Number 21 : Coolant temperature sensor error - DIAG mode 06
 
Error Number 22 : Air intake temperature sensor error - DIAG mode 05
 
Error Number 23 : Ambient air pressure sensor error - DIAG mode 02
 
Error Number 24 : O2 (lambda) sensor error - DIAG mode (none)
 
Error Number 30 : The bike went down - DIAG mode 08
 
Error Number 33 : Coil 1 open circuit - DIAG mode 30
 
Error Number 34 : Coil 2 open circuit - DIAG mode 31
 
Error Number 41 : Tilt sensor error - DIAG mode 08
 
Error Number 42 : Speed sensor error / Neutral sensor in short-circuit - DIAG mode 07-21
 
Error Number 43 : Battery voltage control error - DIAG mode (none)
 
Error Number 44 : EEPROM read/write error - DIAG mode 60
 
Error Number 50 : ECU memory error - DIAG mode (none)
 
Error Er-1 : ECU link error
 
Error Er-2 : ECU link error
 
Error Er-3 : ECU link error
 
Error Er-4 : ECU link error
 
 
 
Following ERROR codes DO NOT allow engine to run :
 
11-12-19-30-41-50 and Er-1 to Er-4
 
Error code 11 allow engine to continue running only if fault appears after engine start.
 
 
 
Following ERROR codes DO allow engine to run but need immediate check because default values are taken by the ECU: 13-14-20-21-22-23-24-24-42-43-44

[ricked1]

Thanks for the info, I saved the codes for later use. I will check the rear abs sensor and the air intake. Sorry the air boot I was referring to is the factory rubber intake on top of the air box. I see some people recommend removing the top of the air box or the rubber intake when using a EJK fuel controller. I made a couple of trips today without any issue, i'm not sure if the error was a fluke or not.